 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| NB2870A Low Power, Reduced EMI Clock Synthesizer The NB2870A is a versatile spread spectrum frequency modulator designed specifically for a wide range of clock frequencies. The NB2870A reduces ElectroMagnetic Interference (EMI) at the clock source, allowing system wide reduction of EMI of all clock dependent signals. The NB2870A allows significant system cost savings by reducing the number of circuit board layers, ferrite beads and shielding that are traditionally required to pass EMI regulations. The NB2870A uses the most efficient and optimized modulation profile approved by the FCC and is implemented by using a proprietary all digital method. The NB2870A modulates the output of a single PLL in order to "spread" the bandwidth of a synthesized clock, and more importantly, decreases the peak amplitudes of its harmonics. This results in significantly lower system EMI compared to the typical narrow band signal produced by oscillators and most frequency generators. Lowering EMI by increasing a signal's bandwidth is called `spread spectrum clock generation'. The NB2870A is targeted towards all portable devices with very low power requirements like MP3 players, Notebooks and digital still cameras. Features http://onsemi.com MARKING DIAGRAM* 6 1 TSOP-6 (TSOT-23-6) SN SUFFIX CASE 318G XXXAYWG G 1 E09 A Y W G = Specific Device Code = Assembly Location = Year = Work Week = Pb-Free Package * * * * * * * * * * Generates an EMI Optimized Clocking Signal at the Output Integrated Loop Filter Components Operates with a 3.3 V / 2.5 V Supply Operating Current less than 4.0 mA Low Power CMOS Design Input Frequency Range: 13 MHz to 30 MHz Generates a 1X Low EMI Spread Spectrum clock of the Input Frequency Frequency Deviation "0.75% (TYP) @ 22 MHz Available in TSOP-6 Package (TSOT-23-6) Pb-Free Package is Available (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. (c) Semiconductor Components Industries, LLC, 2006 December, 2006 - Rev. 3 1 Publication Order Number: NB2870A/D NB2870A VDD XIN/CLKIN XOUT Crystal Oscillator Frequency Divider Feedback Divider REFOUT Modulation PLL Phase Detector Loop Filter VCO Output Divider ModOUT Figure 1. Block Diagram Table 1. KEY SPECIFICATIONS Description Supply Voltages Frequency Range Cycle-to-Cycle Jitter Output Duty Cycle Modulation Equation Frequency Deviation VDD = 3.3 V / 2.5 V VSS Specification 13 MHz < CLKIN < 30 MHz 200 ps (maximum) 45/55% (worst case) FIN/640 "0.75% (TYP) @ 22 MHz REFOUT XOUT XIN/CLKIN 1 2 3 6 VSS ModOUT VDD NB2870A 5 4 Figure 2. Pin Configuration Table 2. PIN DESCRIPTION Pin # 1 2 3 4 5 6 Pin Name REFOUT XOUT XIN/CLKIN VDD ModOUT VSS Type O O I P O P Buffered output of the input frequency. Crystal connection. If using an external reference, this pin must be left unconnected. Crystal connection or external reference frequency input. This pin has dual functions. It can be connected either to an external crystal or an external reference clock Power supply for the entire chip. Spread spectrum clock output. Ground connection. Description http://onsemi.com 2 NB2870A Figure 3. Modulation Profile Table 3. MAXIMUM RATINGS Symbol VDD, VIN TSTG TA Ts TJ TDV Description Voltage on any pin with respect to Ground Storage Temperature Operating Temperature Max. Soldering Temperature (10 sec) Junction Temperature Static Discharge Voltage (As per MIL-STD-883, Method 3015) Rating 0.5 to + 7.0 -65 to +125 0 to 70 260 150 2 Unit V C C C C kV Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. http://onsemi.com 3 NB2870A Table 4. DC ELECTRICAL CHARACTERISTICS FOR 2.5 V SUPPLY (Test Conditions: All parameters are measured at room temperature 25C) Symbol VIL VIH IIL IIH IXOL IXOH VOL VOH IDD ICC VDD tON ZOUT Input LOW Voltage Input HIGH Voltage Input LOW Current Input HIGH Current XOUT Output LOW Current (@ 0.5 V, VDD = 2.5 V) XOUT Output HIGH Current (@ 1.8 V, VDD = 2.5 V) Output LOW Voltage (VDD = 2.5 V, IOL = 8.0 mA) Output HIGH Voltage (VDD = 2.5 V, IOH = 8.0 mA) Static Supply Current (Note 1) Dynamic Supply Current (2.5 V, 22 MHz, and No Load) Operating Voltage Powerup Time (first locked cycle after powerup) (Note 2) Clock Output Impedance 50 2.375 1.8 1.0 3.0 2.5 2.625 5.0 3.0 3.0 0.6 Description Min GND - 0.3 2.0 Typ Max 0.8 VDD + 0.3 -35 35 Unit V V mA mA mA mA V V mA mA V mS W NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. XIN/CLKIN pin is pulled low. 2. VDD and XIN/CLKIN input are stable. Table 5. AC ELECTRICAL CHARACTERISTICS FOR 2.5 V SUPPLY Symbol CLKIN ModOUT fd tLH (Note 3) tHL (Note 3) tJC tD Input Frequency Output Frequency Frequency Deviation Input Frequency = 13 MHz Input Frequency = 30 MHz 0.7 0.4 1.4 0.8 Description Min 13 13 Typ Max 30 30 1.20 0.47 1.6 1.0 200 45 50 55 Unit MHz MHz % ns ns ps % Output Rise Time (measured at 0.7 V to 1.7 V) Output Fall Time (measured at 1.7 V to 0.7 V) Jitter (Cycle-to-Cycle) Output Duty Cycle NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 3. tLH and tHL are measured at capacitive load of 15 pF. http://onsemi.com 4 NB2870A Table 6. DC ELECTRICAL CHARACTERISTICS FOR 3.3 V SUPPLY (Test Conditions: All parameters are measured at room temperature 25C) Symbol VIL VIH IIL IIH IXOL IXOH VOL VOH IDD ICC VDD tON ZOUT Input LOW Voltage Input HIGH Voltage Input LOW Current Input HIGH Current XOUT Output LOW Current (@ 0.4 V, VDD = 3.3 V) XOUT Output HIGH Current (@ 2.5 V, VDD = 3.3 V) Output LOW Voltage (VDD = 3.3 V, IOL = 8.0 mA) Output HIGH Voltage (VDD = 3.3 V, IOH = 8.0 mA) Static Supply Current (Note 4) Dynamic Supply Current (3.3 V, 22 MHz, and No Load) Operating Voltage Powerup Time (first locked cycle after powerup) (Note 5) Clock Output Impedance 45 2.7 2.5 1.2 4.0 3.3 3.6 5.0 3 3 0.4 Description Min GND - 0.3 2.0 Typ Max 0.8 VDD + 0.3 -35 35 Unit V V mA mA mA mA V V mA mA V mS W NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 4. XIN/CLKIN pin is pulled low. 5. VDD and XIN/CLKIN input are stable. Table 7. AC ELECTRICAL CHARACTERISTICS FOR 3.3 V SUPPLY Symbol CLKIN ModOUT fd tLH (Note 6) tHL (Note 6) tJC tD Input Frequency Output Frequency Frequency Deviation Input Frequency = 13 MHz Input Frequency = 30 MHz 0.4 0.3 1.2 0.8 Description Min 13 13 Typ Max 30 30 1.20 0.47 1.5 1.1 200 45 50 55 Unit MHz MHz % ns ns ps % Output Rise Time (measured at 0.8 V to 2.0 V) Output Fall Time (measured at 2.0 V to 0.8 V) Jitter (Cycle-to-Cycle) Output Duty Cycle NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 6. tLH and tHL are measured at capacitive load of 15 pF. http://onsemi.com 5 NB2870A XIN Crystal XOUT R1 = 510 W C1 = 27 pF C2 = 27 pF Figure 4. Typical Crystal Oscillator Circuit Table 8. TYPICAL CRYSTAL SPECIFICATIONS Fundamental AT Cut Parallel Resonant Crystal Nominal Frequency Frequency Tolerance Operating Temperature Range Storage Temperature Load Capacitance Shunt Capacitance ESR 14.31818 MHz 50 ppm or better at 25C -25C to +85C -40C to +85C 18 pF 7 pF Maximum 25 W http://onsemi.com 6 NB2870A ORDERING INFORMATION Device NB2870ASNR2 NB2870ASNR2G Marking E09 E09 Temperature Range 0C - 70C 0C - 70C Package TSOP-6 (TSOT-23-6) TSOP-6 (TSOT-23-6) (Pb-Free) Shipping 2500 Tape & Reel 2500 Tape & Reel Availability Now Contact Sales Representative For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 7 NB2870A PACKAGE DIMENSIONS TSOP-6 CASE 318G-02 ISSUE S D NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. DIM A A1 b c D E e L HE q MIN 0.90 0.01 0.25 0.10 2.90 1.30 0.85 0.20 2.50 0 MILLIMETERS NOM MAX 1.00 1.10 0.06 0.10 0.38 0.50 0.18 0.26 3.00 3.10 1.50 1.70 0.95 1.05 0.40 0.60 2.75 3.00 10 - MIN 0.035 0.001 0.010 0.004 0.114 0.051 0.034 0.008 0.099 0 INCHES NOM 0.039 0.002 0.014 0.007 0.118 0.059 0.037 0.016 0.108 - MAX 0.043 0.004 0.020 0.010 0.122 0.067 0.041 0.024 0.118 10 HE 6 1 5 2 4 3 E b e c L q 0.05 (0.002) A1 A SOLDERING FOOTPRINT* 2.4 0.094 1.9 0.075 0.95 0.037 0.95 0.037 0.7 0.028 1.0 0.039 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. This product utilizes US Patent #6,646,463 Impedance Emulator Patent issued to Alliance Semiconductor, Dated 11-11-2003. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative http://onsemi.com 8 NB2870A/D |
Price & Availability of NB2870ASNR2
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |